22 caliber gun which marketed itself as “especially for youth shooters.” Instead of massive public backlash, the National Rifle Association (NRA) instead, days after the event, held its Annual Meeting where it explicitly marketed firearms and firearm paraphernalia to kids, including NRA bibs for children, ‘Youth Model’ firearms, and NRA publications focused on ‘Youth Shooters.’ Where was the outcry over the blatant militarization of children by one of the most powerful political lobbies in the United States? Where was the parental campaigns demanding that children not be subject to the propagandization of firearms? Where are the restrictions, the regulations, the bans? The NRA’s response, instead, sent a different message: “You’ll have to take my gun from my child’s cold, dead hands.Frank Lampard's four potential options amid miserable return as interim Chelsea boss Now examine how differently our society treats guns in a similar context: On April 20th, 2013, a five-year-old Kentucky boy shot and killed his two-year-old sister with a gun that had been specifically manufactured for child use. So when parents observed that these unnecessarily dangerous toys were injuring and killing their children, they did what any sensible parent would do: they complained until the government listened. The problem wasn’t just that lawn darts were dangerous, it was that they were dangerous AND they were being marketed to children as a game, despite being responsible for 6,100 emergency room visits over a span of eight years. To this day, it is illegal to assemble a lawn dart in either of the two countries. The campaign led to an all-out ban in the US and Canada. Michelle’s father immediately began a campaign to ban the darts, arguing that anything less than a full-scale ban would be insufficient-after all, even if you were to ban lawn darts in your own home, nothing can stop a neighbor’s child from throwing one over the fence. These darts were part of a children’s game in the 70′s and 80′s involving large, weighted darts with sharp metal tips, designed to pierce a horizontal target on the ground. In April 1987 seven-year-old Michelle Snow was killed in Riverside, California by a stray lawn dart that was thrown by her brother’s playmate. A New York Times’ piece added to the controversy showing that, due to idiosyncrasies over what constitutes a ‘homicide’ or an ‘accident’, child firearm accidental killings happen roughly twice as much as they are reported in national databases. In both cases, the deaths were a result of improperly secured weapons. The BBC originally reported on this phenomenon in 2009 when, in the span of 24 hours, two children were shot by their toddler siblings. And this statistic represents only data for which a toddler is the shooter in a death (MotherJones reports that 71 children have been killed by guns since Newtown). Ten more toddlers have accidentally shot themselves or somebody else this year. Since January 1st, 2013 there have been 11 reported gun fatalities involving preschool children as the shooter. He believed he had removed the bullets, and so jokingly pulled the trigger. Cassie Culpepper, age 11, was riding in the back of a pickup when her 12-year-old brother pointed his father’s pistol at her.
0 Comments
b) Within eligible states, priority will be given to projects located in the North Core, South Core, West Core, and Overwintering Monarch Conservation Units (Figure 2).a) Grant funding will be awarded in the following eligible states: Arizona, Arkansas, California, Colorado, Idaho, Illinois, Indiana, Iowa, Kansas, Michigan, Minnesota, Missouri, Montana, Nebraska, Nevada, New Mexico, North Dakota, Ohio, Oklahoma, Oregon, South Dakota, Texas, Utah, Washington, Wisconsin, and Wyoming. They represent priority, but not exclusive, areas for NFWF investments in monarch conservation through the category “Technical Assistance for Private Working Lands.” 2. These focal geographies include partial Monarch Conservation Units defined by the U.S. c) Projects are restricted to private working lands.įigure 1 (Below).b) Within eligible states, priority will be given to projects located in the North Core and South Core Monarch Conservation Units (Figure 1).a) Grant funding will be awarded in the following eligible states: Illinois, Indiana, Iowa, Kansas, Minnesota, Missouri, Ohio, Oklahoma, Texas, and Wisconsin.Technical Assistance for Private Working Lands Fish and Wildlife Service (USFWS), Bureau of Land Management (BLM), and U.S. Funding is provided by Bayer Crop Science, Scotts Miracle-Gro Foundation, Natural Resources Conservation Service (NRCS), U.S. The Pollinator Fund will award up to $1.9 million in grants in 2022: up to $600,000 for Technical Assistance for Private Working Lands and up to $1.3 million for Habitat Improvement. Technical Assistance for Private Working Lands. Grants will be awarded in two categories: The most competitive projects will demonstrate clear benefits to both the monarch butterfly and additional at-risk native insect pollinator species (i.e., federally listed, candidate, or proposed native insect pollinator species). The goal of the Monarch Butterfly and Pollinators Conservation Fund (Pollinator Fund) is to protect, conserve, and increase habitat for the monarch butterfly and other native insect pollinators. The National Fish and Wildlife Foundation (NFWF) is soliciting proposals to advance pollinator conservation. Pre-Proposal Due Date: Thursday, May 5 by 11:59 PM Eastern Timeįull Proposal Due Date: Thursday, July 7 by 11:59 PM Eastern Time OVERVIEW Applicant Webinar : Thursday, Ap3:00 PM to 4:00 PM Eastern Time Seats of eDrawings Professional can be purchased as standalone or network licenses. Original material relating to this topic can be found in the SOLIDWORKS Customer Portal Knowledge Base, solution articles S-037765 & S-046922.Īnybody can download the eDrawings viewer. The eDrawings interface has tools, menus, and a graphics area. It will be review-enabled, allowing mark-up and (optionally) measure. If it passes the check, the file will be saved out of SOLIDWORKS as if it were saved from eDrawings Professional. Download eDrawings The download wizard will allow you to download the eDrawing viewer as well as the eDrawings publisher. edrw) from SOLIDWORKS Standard, SOLIDWORKS will perform a check to see if eDrawings Professional has been installed on the same machine. When saving SOLIDWORKS files as eDrawing files (.eprt. Communication and approval processes become. SOLIDWORKS Standard and eDrawings Pro on the Same Computer eDrawing Viewer enables anyone to view 3D CAD design without having to purchase and install a 3D CAD software. However, the eDrawings Viewer can measure eDrawing files exported from SOLIDWORKS Professional or Premium, provided the enable measure option has been turned on. Moreover, the eDrawings Viewer cannot measure eDrawing files exported from SOLIDWORKS Standard, even if the enable measure option has been turned on. It is not possible to measure within SOLIDWORKS files. The eDrawings Viewer is intended primarily for users who need to consume and understand 3D product data, but not use CAD, create, or publish eDrawings files. Working within the eDrawings Viewer (eDrawings Standard) eDrawings is free software that lets you view and print eDrawings (eDRW, ePRT, eASM), native SolidWorks documents (sldprt, sldasm, slddrw), DXF, and DWG format files. There is also an enable measure option in eDrawings Pro that can be found near the bottom of the Save As window. The enable measure option must be turned on, and is accessible via the Options button when using the File > Save As command to save an eDrawing file from SOLIDWORKS. Measuring within SOLIDWORKS files and eDrawings files exported from SOLIDWORKS Standard is possible. |